Alarm Lock PL6100 User Manual download pdf (Page 7)

Wireless Lock Hardware Guide 7

ACTIVITY LED SOUNDER COMMENTS

Valid Credential or

Remote Input / Bypass

3 Green Flashes 3 Beeps Normal Operation

Invalid Credential 7 Red Flashes 7 Beeps

Card Detection / Reader Disabled 2 Green Flashes 2 Beeps

"Card Detection": Badge presented to lock reader to test if

the badge type is compatible with the system.

"Reader Disabled": Programmed using CA3000 software.

Waiting Indication

Slow green flashes for pro-

grammed duration (varies

with reader settings)

Used when "Card & Code" or "Two Person Reader" is

enabled

Low Battery --

Continuous beep for

length of "Door Strike

Time"

See "CPL6100 BATTERY REPLACEMENT" on this page

above.

Lock Restarts with Configuration Data

• 3 short beeps sound (NO LED's flashing);

• short pause;

• 3 short beeps sound with 3 green LED's.

When power re-applied to a lock that has already been

configured and operational (with badge data, etc.), or

when replacing batteries. Configuration data retained, no

need for data download.

Lock Restarts without Configuration Data

• 3 short beeps sound (NO LED's flashing);

• short pause;

• 3 short beeps sound with 3 red LED's.

When power re-applied to a lock that has already been

configured and operational (with badge data, etc.), or

when replacing batteries. Configuration data lost or cor-

rupted, lock will automatically request configuration data

from CA3000.

With a fully charged battery, the CPL6100 LED and sounder feedback is as follows:

Alarm Lock PL6100 / Continental CPL6100

ing an existing lock to a new door, and the lock must be

dismantled and powered down for an extended time pe-

riod), proceed as follows:

1. Disconnect battery pack connector.

2. With battery power removed, short the two white wires

(Remote Input / Bypass wires) together for 10 sec-

onds to ensure discharge of all capacitors.

Do NOT plug in the yellow wire shunt connector

(Erase Memory Leads--DO NOT CONNECT).

3. Re-connect battery pack (lock will sound 3 short

beeps). If these 3 beeps are not heard, then repeat

steps at step 1. Observe lock carefully:

• 3 short beeps sound (NO LED's flashing);

• short pause;

• 3 short beeps sound with 3 green LED's.

The 3 green LED's indicate the lock configuration

data (badge data, etc.) is retained successfully, and

the lock is ready for use. If you see 3 red LED's, this

indicates the lock started without configuration data,

and will automatically request configuration data from

CA3000.

CPL6100 BATTERY REPLACEMENT

Upon a badge presentation when the batteries are weak,

the lock sounder will continuously beep for the length of

the "Door Strike Time" ("Door Strike Time" is the duration

the lock would remain unlocked when a valid badge is

presented). For models with a replaceable battery pack,

use four (4) C-size 1.5 volt alkaline batteries. For models

with a sealed battery pack, contact your Alarm Lock

dealer for a replacement battery pack. Always replace

weak batteries as soon as possible.

1. At the back of the lock, remove the screw at the bot-

tom of the lock housing and remove the cover.

2. Disconnect the battery pack, removing power.

3. With battery power removed, short the two white wires

(Remote Input / Bypass wires) together for 10 sec-

onds to ensure discharge of all capacitors.

Do NOT plug in the yellow wire shunt connector

(Erase Memory Leads--DO NOT CONNECT).

4. Re-connect battery pack and observe lock carefully:

• 3 short beeps sound (NO LED's flashing);

• short pause;

• 3 short beeps sound with 3 green LED's.

The 3 green LED's indicate the lock configuration data

(badge data, etc.) is retained successfully, and the

lock is ready for use. If you see 3 red LED's, this indi-

cates the lock started without configuration data, and

will automatically request configuration data from

CA3000.

5. Replace the cover and tighten the screw.

Note: Restarting an operational lock may send a Lock

Startup event to the CA3000 GUI.

CPL6100 LED and Sounder Indicators

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Alarm Lock PL6100 User Manual Page 7

Comments to this Manuals