Alarm Lock DL1300 Instruction Manual download pdf (Page 11)

WIRING

See the Installation Manual for more information.

Batteries:

Use only 3.0 volt Lithium Type 123 batteries (or equiva-

lent). Two (2) batteries of this type are needed.

BATTERY REPLACEMENT

When a valid code is entered and the batteries are weak, the

red & green LED's will light and the sounder will sound for 4

seconds. Replace with two (2) 3.0 volt Lithium Type 123

batteries. Always replace weak batteries as soon as

possible.

CAUTION: Do not press any keys while batteries are

disconnected or you may erase the real-time clock

settings.

1. Insert key in cylinder and turn counterclockwise to allow

access to the battery compartment screw. With the sup-

plied 5/64" Allen wrench, loosen the battery cover

screw only until the battery cover is able to slide off.

2. Pull out the battery pack and quickly replace both

batteries - within 1 minute.

3. If you do not hear the 3 beeps when power is re-applied,

all programming and settings have been retained, and the

lock is ready for use. Go to step 5.

4. If you do hear 3 beeps when power is re-applied, do not

press any keys for 15 seconds. After the 15 second

period, the LED will flash red 6 times and 6 beeps will

sound. Reset the clock using functions 38, 39 and 40.

5. Slide the battery cover back in place and tighten the

screw.

POWER UP

• When applying power to the lock for the first time, stop

and follow the procedure outlined in "Quick Start, First

Time Start Up" on page 12.

• When power is re-applied to a lock that was already op-

erational, proceed as follows:

1. Disconnect battery pack connector.

2. With battery power disconnected, press and hold

down ; for 10 seconds to ensure discharge of all

capacitors.

3. Re-connect battery pack (lock will sound 3 short beeps).

If beeps are not heard, then restart at step 1.

4. Do not press any keys for 15 seconds.

5. After 15 seconds, the LED will flash red 6 times and 6

beeps will sound.

The lock is now ready for use. The pre-existing program is

loaded from fixed memory. Reset the clock using functions

38, 39 and 40 if necessary.

ERASE ALL PROGRAMMING

RESTORE FACTORY DEFAULT (original "out of box" set-

tings that were set at the factory will be loaded).

1. Enter the current Master Code (if not known, proceed

directly to ALTERNATIVE METHOD, below). Wait for

the green light and press ; until multiple beeps are

heard. You are now in Program Mode.

2. Press ; 99 ; 000 :.

3. Listen for 6 beeps. The lock will re-lock. All settings and

programming have been erased. Proceed directly to

page 12, Quick Start, and follow the procedure "Enter

Program Mode and Change Factory Master Code".

ALTERNATIVE METHOD

Note: This method requires the lock first be removed from

the door.

1. Insert key in cylinder and turn counterclockwise to allow

access to the battery compartment screw. With the sup-

plied 5/64" Allen wrench, loosen the battery cover

screw only until the battery cover is able to slide off.

2. Disconnect the battery pack.

3. Remove the back plate by unscrewing the two Phillips

head screws. Note: Some models have four Phillips

head screws. Be careful not to damage the motor drive

wires.

4. Locate jumper header JP1 near the top of the printed

circuit board and install the jumper (provided) across pins

1 and 2 of JP1.

5. Press and hold down ; for 10 seconds (to ensure

all power is drained from the lock) and release.

6. Connect the batteries and--within 5 seconds--press and

hold ;. After hearing 6 additional beeps, re-

lease ;. If you do not hear these 6 additional

beeps, you must start over at step 2. Failure to follow

this exact procedure can result in erratic lock behavior.

7. Test by pressing the default Master Code of

123456 (a beep will sound

and the lock will unlock).

8. Remove the jumper from JP1 pins 1 and 2 and place

jumper on 1 pin for storage.

9. Carefully reinstall the back plate STRAIGHT onto the

lock body. Be careful not to pinch or damage the motor

drive wires. While inserting the back plate, be sure the

rear pin of the tailpiece inserts into the spindle hole--

check this alignment after installation by pushing on the

spring-loaded tailpiece to verify that it smoothly moves

up and down. Replace the two (or four) Phillips head

screws to secure the back plate. Note: It may be nec-

essary to tighten the battery screw previously loosened

in step 1.

10. Re-mount the lock on the door. With the battery back

inside its compartment, slide the battery cover back in

place and tighten the screw.

All settings and programming have been erased. Pro-

ceed directly to page 12, Quick Start, and follow the

procedure "Enter Program Mode and Change Factory

Master Code".

Wiring and Power Up

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 35 36

Comments to this Manuals

No comments

Alarm Lock DL1300 Instruction Manual Page 11

Comments to this Manuals

Related products and manuals for Security access control systems Alarm Lock DL1300