NetworX Series™ NX-4 Control Panel Installation and Startup UL approved for ANSI/SIA CP-01-2000
NX-4 Control Page 8 PROGRAMMING THE LED KEYPADS This section describes how to program the address of each keypad as well as the options that are
NX-4 Control Page 9CHANGING USER CODES: 1. Enter [r]-[5]-[master code]. The "Ready" LED will flash. 2. Enter the 2 digit user num
NX-4 Control Page 10 PROGRAMMING THE NX-4 CONTROL ENTERING THE PROGRAM MODE: To enter the Program Mode, press [r]-[8]. At this time, the five f
NX-4 Control Page 11PROGRAMMING EXAMPLE – FIGURE 1 (Numerical Data) Zone 1 LED = 1 Zone 4 LED = 8 } Data = 9 Zone 2 LED = 2 Zone 7 LED = 64 } Dat
NX-4 Control Page 12 FEATURE SELECTION DATA: Feature selection data will display the current condition (on or off) of eight features associated wi
NX-4 Control Page 13FORMAT SELECTIONS DATA FORMAT DESCRIPTION 0 Local Communicator is disabled 1 Universal 4+2 Two digit event code 180
NX-4 Control Page 14 LOCATION 6 - PROGRAMMING PHONE #2 (20 segments, numerical data) Phone #2 is programmed in location 6. A "14" indi
NX-4 Control Page 15LOCATION 12 - PROGRAMMING PHONE #3 (20 segments, numerical data) Phone #3 is programmed in location 12. A "14" in
NX-4 Control Page 16 LOCATION 18 - CUSTOM COMMUNICATOR FORMAT (See locations 2, 8, & 14) Segment 1: 1 = On for 1800hz transmit; Off for 1900
NX-4 Control Page 17Segment 2: 1 - On enables the LED Extinguish feature. 2 - On enables the Require Code for Bypassing feature. 3 - On enables t
© 2012 UTC Fire & Security Americas Corporation, Inc. Interlogix is part of UTC Climate Controls & Security, a unit of United Technologi
NX-4 Control Page 18 Segment 4: 1 - On if Fail To Communicate report enabled. 2 - On if Log Full report enabled. 3 - On if Autotest report enable
NX-4 Control Page 19LOCATION 41 - CODE REQUIREMENTS (1 segment, feature data) Segment 1: 1 = On enables the 6-digit code option. If 6-digit o
NX-4 Control Page 20 AUXILIARY OUTPUT EVENT SELECTION DATA EVENT DATA EVENT 0 / Burglary Alarm 26 Fire Trouble 1 / Fire
NX-4 Control Page 21LOCATION 52 - OPENING TIME (2 segments, numerical data) Location 52 contains the time in 24 hour format the NX-4 enables cod
NX-4 Control Page 22 COMMUNICATOR CODES FOR SLOW FORMATS ONLY LOCATIONS 56- 83 ARE ONLY USED WHEN REPORTING EVENTS TO A PAGER OR USING A SLOW FO
NX-4 Control Page 23LOCATION 68 - AAC FAIL / AC FAIL RESTORE@ CODES (4 segments, numerical data) Location 68 contains the tens and ones digits fo
NX-4 Control Page 24 LOCATION 81 - ASTART PROGRAM AND END PROGRAM@ CODES (4 segments, numerical data) Location 81 contains the tens and ones digi
NX-4 Control Page 25LOCATIONS 112 THRU 149 contain the remaining 19 Customized Zone Group information. The even numbered locations reflect the AG
NX-4 Control Page 26 PROGRAMMING WORKSHEETS ? Factory defaults for segments are in bold italics text. Some locations are reserved and have been i
NX-4 Control Page 27 LOC PG DESCRIPTION DEFAULT DATA FORMAT OVERRIDE Segment #1 (Circle Numbers To Program) Segment #2 (Circle Numb
NetworX NX-4 Control/Communicator Installation Manual Page General Description...
NX-4 Control Page 28 LOC PG DESCRIPTION DEFAULT DATA SIREN AND SYSTEM SUPERVISION Segment #1 (Circle numbers to program) 37 17 1 2 3 4
NX-4 Control Page 29 LOC PG DESCRIPTION DEFAULT DATA KEYPAD SOUNDER CONTROL Segment #1 (Circle numbers to program) 39 18 1 2 3 4 5 6
NX-4 Control Page 30 LOC PG DESCRIPTION DEFAULT DATA AUXILIARY OUTPUT #1, EVENT & TIME Segment #1: Program the event number for outpu
NX-4 Control Page 31LOC PG DESCRIPTION DEFAULT DATA 64 22 AUXILIARY 2 0-0 _ _ 65 22 KEYPAD PANIC 0-2 _ _ 66 22 KEYPAD MULTIPLE CODE EN
NX-4 Control Page 32 THE DEFAULTS LISTED IN THE ODD NUMBERED LOCATIONS BELOW REPRESENT THE THREE SEGMENTS OF EACH OF THOSE LOCATIONS. USE THE THR
NX-4 Control Page 33APPENDIX 1 REPORTING FIXED CODES IN CONTACT ID AND SIA The table below list the event codes sent for the following reports (i
NX-4 Control Page 34 APPENDIX 2 REPORTING ZONE CODES IN SIA OR CONTACT ID The NX-4 has the ability to report SIA level 1 transmissions to either
NX-4 Control Page 35APPENDIX 3 EXPANDER NUMBERS FOR REPORTING EXPANDER TROUBLE The tables below list the device numbers that will be reported for
NX-4 Control Page 36 WIRING DIAGRAM
NX-4 Control Page 37TERMINAL DESCRIPTIONS TERMINAL DESCRIPTION R1 House Telephone Ring (Grey). R Telephone Ring (Red). T Telephone Tip (
NX-4 Control Page 2 IMPORTANT NOTES GENERAL DESCRIPTION The NetworX NX-4 represents a new approach to security systems design. Drawing on our
NX-4 Control Page 38 Notices (Applies to products which have the CE mark attached) DECLARATION OF CONFORMITY Manufacturer’s Name: Caddx Contr
Page 39LOCAL TELEPHONE COMPANY INTERFACE INFORMATION TELEPHONE CONNECTION REQUIREMENTS Except for telephone company provided ringers, all connect
Page 40 UNDERWRITERS LABORATORIES INFORMATION The NetworX NX-4 holds the following listings from Underwriters Laboratories (US and Canada): House
SIA SYSTEM REQUIREMENTS (ANSI-SIA CP-01) To meet SIA CP-01 requirements – • Minimum System Requirements: 1 control panel; 2 keypads • Remote arm
SPECIFICATIONS OPERATING POWER 16.5 VAC 25, 40, or 50 VA Transformer AUXILIARY POWER w/25 VA Transformer 12 VDC Regulated 500 mA
NX-4 Control Page 3FEATURE DEFINITIONS Abort If enabled, the NX-4 will wait the programmed number of seconds in location 40 prior to sending a
NX-4 Control Page 4 Built In Siren Driver The NX-4 has a built-in 112db siren driver. When desired, this built-in driver can be easily conver
NX-4 Control Page 5Exit Error If enabled, the NX-4 will send an "Exit Error Report" if an entry/exit zone is faulted at the instant th
NX-4 Control Page 6 Local Programming Lockout This feature will disable programming of all locations or specified locations from the keypad. (
NX-4 Control Page 7 Swinger Shutdown This feature allows a zone(s) to be automatically bypassed after a specified number of alarms. When a zone
Comments to this Manuals