Alarm Lock NETWORXPANEL Specifications download pdf (Page 11)

NX-592E NetworX Cellular Module Installation Sheet

• Only the lower outlet is controlled by Z-Wave. Ensure you

are plugging devices into the lower outlet while testing if

the outlet works for Z-Wave control. The opposite is true if

the device is installed upside down.

Locks

Note: If the security panel cannot be taken to within 6 ft. of the

lock installation location, add the lock to the system first as

directed beginning in step 2. (You will need to connect the

battery pack to the keypad before attempting to perform these

steps.)

Tips

• Before removing old locks or beginning installation, check

the layout of the door to make sure the new lock will not

conflict with existing hardware.

• Contact a locksmith if you experience difficulties removing

old hardware or installing the new lock.

• Send user codes to the lock (via the customer website -

see step 4) before leaving the property. Alarm.com does

not recommend programming codes locally via the lock

keypad - all codes should be programmed through the

Alarm.com interface.

• Ask your customer to save the programming code that

comes with the lock (Schlage only). This will be

convenient to have if they ever have issues in the future.

Schlage lever lock or Schlage deadbolt

1. Follow the instructions included with the lock. When

prompted to continue setup online, do the following steps

to program the lock into the Concord panel.

2. Enter Add mode on the security panel.

3. On the lock keypad, enter the six-digit programming code

(given by Schlage), then press the Schlage button,

followed by 0. The Schlage button will flash green

(Figure 7 below).

Note: Wait until the light flashes green before disrupting

the lock or panel. Failure to do so will result in lock

malfunctions.

Figure 7: Schlage lock

4. Login online to the customer account at www.alarm.com to

select which user codes are allowed to use this lock. To

do this, go to the emPower then Locks tab. On the User

Code table, you will see a column labeled Lock Access.

Check the box of the lock you want to allow each user

code to access.

Tip

If you observe a red blinking light at the end of the installation

keystrokes instead of green, follow these instructions:

1. Enter the panel into Delete mode (see “Deleting a Z-Wave

device (Device Exclusion)” on page 9).

2. Enter the six-digit programming code on the keypad and

wait for three orange lights and three beeps.

3. Press the Schlage button and then 0 on the keypad. Wait

for three orange lights and three beeps.

4. Wait for all lights to stop blinking. You should now be able

to enroll the lock normally by repeating the steps shown

above (after re-entering Add mode).

Kwikset deadbolt

1. Follow all instructions provided to install the lock onto the

door and double-check that the programmable keypad

lock works.

2. Enter the panel into Add mode.

3. To trigger the lock to add it, press button “B” (Figure 8

below).

Note: Wait until the red light (under the paper next to

button “B”) stops flashing before disrupting the lock or

panel. Failure to do so will result in lock malfunctions.

4. Login online to the customer account at www.Alarm.com

to select which user codes are allowed to use this lock. To

do this, go to the emPower then Locks tab. On the User

Codes table, you will see a column labeled Lock Access.

Check the box of the lock you want to allow each user

code to access.

Figure 8: Lock trigger button

Thermostats

Tips

• The new thermostat should be placed in the same location

as the original thermostat unless an HVAC professional

approves the new location.

• Learn the thermostat into your emPower network while it is

powered using the power source (AC power vs. battery

power) it will use during regular use after installation.

UTC Z-Wave Thermostat

1. Follow the manufacturer’s instructions to install the

thermostat.

2. Enter Add mode on your panel.

3. Under the top cover of the thermostat, press the black

Mate button located in the upper right hand side.

Note: The thermostat should be connected to AC before it

is learned into the network.

1 2 ... 6 7 8 9 10 11 12 13

Comments to this Manuals

No comments

Alarm Lock NETWORXPANEL Specifications Page 11

Comments to this Manuals

Related products and manuals for Security access control systems Alarm Lock NETWORXPANEL